BlueMod+C11/G2 R e l a s e N o t e s Copyright (c) 2009 Stollmann E+V GmbH. All rights reserved. Version 1.208.4 - Jun 8 2009 - ===================================================== Notes Changes / New Features - none Changes / Fixed Bugs - #0003328: reduced RF output power and range with HW ID >= 4 when remote side supports EDR Internal Changes Known Bugs Not implemented Features -------------------------------------------------------------------------------- Version 1.208.2 - Mar 26 2009 - ===================================================== Notes Changes / New Features - none Changes / Fixed Bugs - #0003098: UART IF; data transfer to host stalls when RTS line is changed manually by removing and plugging the jumper on the eva board - #0003162: UART IF: device no longer reacts on changes on the RTS line - #0003096: tx on UART: about 2 single char per MB get lost when host uses hw flowcontrol Internal Changes Known Bugs Not implemented Features -------------------------------------------------------------------------------- Version 1.208.1 - Jan 21 2009 - ===================================================== Notes Changes / New Features - #0002859: Remove toggle of /LED1 signal during device initialisation Changes / Fixed Bugs - none Internal Changes Known Bugs Not implemented Features -------------------------------------------------------------------------------- Version 1.208 - Oct 20 2008 - Release Candidate ===================================================== Notes Changes / New Features - #0002483: Length of device names for device discovery shall be extended to 50 visible characters - #0002487: Support of RS485 Changes / Fixed Bugs - #0002484: Device performs reset during service discovery to a remote device with friendly name >=29 characters - #0002416: Sometimes device stalls unpredictable for 1 sec, transmission delay is enlarged - #0002421: DTR detection with SerialTester script fails - #0002123: Characters get lost if sending data starts direct after CONNECT Internal Changes Known Bugs Not implemented Features -------------------------------------------------------------------------------- Version 1.207.7 - Oct 17 2008 - ES ===================================================== Notes Changes / New Features - #0002482: Length of device names for device discovery shall be extended to 50 visible characters Changes / Fixed Bugs - #0002407: Device performs reset during service discovery to a remote device with friendly name >=29 characters Internal Changes Known Bugs Not implemented Features -------------------------------------------------------------------------------- Version 1.207.4 - Feb 11 2008 - ===================================================== Notes Changes / New Features - new Feature: power down mode - new Feature: DCE/DTE switching - #0001284: "rsttim" parameter listed by call of "show" command - #0001285: "rstmsg" parameter listed by call of "show" command - #0001549: easy access to "Enable Device Under Test Mode" by command "bedutm" Changes / Fixed Bugs - BUG#0001195: configurator is not responsible after reset if "rstmsg" set to 0 - BUG#0001196: changing the Link Supervision Timeout not possible by slave - BUG#0001200: copy protection does not work - BUG#0001277: parameter "rstmsg" has wrong default value - BUG#0001456: C11/G2: connection establishment unstable - fix rx character lost (error effect: inquiry or connection could not be initiated after startup) - BUG#0001388: C11/G2: NV-RAM reset to factory settings - fix eeprom write operation (error effect: default parameter values were displayed after reset or power cycle) - BUG#0000477: data transfer stops after "bsname" parameter changed via config port - BUG#0000524: input of 50 characters long "bname" causing device reset - BUG#0000618: value range of parameter "ridle" differ from specification - BUG#0000817: dialing atdd16 returns ERROR - BUG#0001002: parameter "devmode" and "devmsel" not implemented - BUG#0001011: no Bluetooth address after CONNECT response with extended response enabled - BUG#0001012: C11/G2: "Long Init String" fails - BUG#0001287: parameter "ridle" should not be hidden anymore - BUG#0001574: wrong default value of BPSRW parameter - BUG#0001575: wrong default value of BPSRI parameter - BUG#0001576: BPSRI parameter does not work properly - BUG#0001577: BPSRW parameter does not work properly - BUG#0001587: release bleutooth connection in sleep mode - in sleep mode the user uart is now disabled - BUG#0001589: no prompt after change "rbaccl" parameter from remote session - BUG#0001592: too high current consuption in Power Down/Deep-Sleep states - BUG#0001698: bsmin can be greater than bsmax - BUG#0001670: sniff mode works although if sniff parameter (bsmin & bsmax) are different in DUT and remote device - BUG#0001694: C11/G2: ZModem data transfer between two C11/G2(A06(!)-modules) hangs - BUG#0001703: sniff mode does not work if ranges of sniff interval on both sides partial overlapped and "bsmax"s are different - BUG#0001707: connection initiate not possible after release previous connection in "command online" state Internal Changes Known Bugs Not implemented Features -------------------------------------------------------------------------------- Version 1.206.3 - Oct 29 2007 - ====================================================== Notes - maintenance version Changes / Fixed Bugs - 0001462: [Bug] C11/G2: reaction time on changes of RTS input signal to long, too much tx character backlash - 0001388: [Bug] C11/G2: NV-RAM reset to factory settings - 0001456: [Bug] C11/G2: connection establishment unstable Internal Changes Known Bugs - #0001011: no Bluetooth address after CONNECT response with extended response enabled - #0001199: "NO CARRIER" when "BROLE=1" and Slave setting BROLE=4 - #0001196: changing the Link Supervision Timeout not possible by slave Not implemented Features - Power down modi - DTE Mode -------------------------------------------------------------------------------- Version 1.206.1 - Aug 27 2007 - ====================================================== Notes - maintenance version Changes - fixed bug #0001238: RSSI Querry - command BARSSI broken - new parameter BARSSIIO - new feature RSSI signaling on IO lines IO5(P_ABS_RSSI_IO2) IO8(P_ABS_RSSI_IO1) IO10 (P_ABS_RSSI_IO0) 1 0 0 very near >= -30 dB 1 0 1 very near >= -30 dB 0 0 0 OK < -30 dB 0 0 1 OK < -45 dB 0 1 0 OK < -60 dB 0 1 1 OK < -70 dB 1 1 0 far away < -83 dB 1 1 1 far away < -90 dB Internal Changes Known Bugs - #0001011: no Bluetooth address after CONNECT response with extended response enabled - #0001199: "NO CARRIER" when "BROLE=1" and Slave setting BROLE=4 - #0001196: changing the Link Supervision Timeout not possible by slave Not implemented Features - Power down modi - DTE Mode -------------------------------------------------------------------------------- Version 1.206 - Jul 26 2007 - ==================================================== Notes - first released version Changes Internal Changes Known Bugs - #0001011: no Bluetooth address after CONNECT response with extended response enabled - #0001199: "NO CARRIER" when "BROLE=1" and Slave setting BROLE=4 - #0001196: changing the Link Supervision Timeout not possible by slave Not implemented Features - Power down modi - DTE Mode -------------------------------------------------------------------------------- Version 1.xx - - ===================================================== Notes Changes Internal Changes Known Bugs Not implemented Features --------------------------------------------------------------------------------